Tianjin Weilei Technology Ltd.

Homepage:Login:Register:Soul:Top Host

Forum style

Interface Style:

Total 1464,Total 30 pages

[<<][16][>>]

Copying ST nand512w3a2cn6 chip

PhilipB

I have a Wellon VP-980 with a TSOP48 adapter. I have a known good working chip that I"m trying to duplicate, I can read the chip and successfully verify the image against the chip but when I put the copied chip into the device it does not work even though Wellon indicates its identical. I"ve also found that not all of the new blank chips will program. The software we are using is version 4.2.0 and I think this is the latest version for my programmer.

Last post : Re:Copying ST nand512w3a2cn6 chip	Reply: myx1
the nand has bad blocks so not all of them will program successfully. the chip has the unique serial number.it is made by IC Manufacter for　 copyright protection. if your system uses it,the device will not work even the chip programmed the same data.

All replies (1)

[ Posted:2013-11-06 20:23:04 ]

series MX29GA128EHXC not VP890

@eparator

Please add the systems with series MX29GA128EHXC-BGA64
Programator VP890

Last post : Re:series MX29GA128EHXC not VP890	Reply: @eparator
Thanks guessed already.

All replies (2)

[ Posted:2013-11-05 14:47:50 ]

VP-990-74HC594D

denis500

Please add ic 74hc594d　to TTL CMOS Test

Reply the message

[ Posted:2013-10-29 00:07:05 ]

Vp280

kyo

Please i need help with Vp280: Device Atmel At89c55WD software version 4.3.4 and version 4.6.0 Program fail. Best regards

Last post : Re:Vp280	Reply: lxl
maybe VP-280 is bad.

All replies (5)

[ Posted:2013-10-22 02:52:19 ]

vp-890

aiman said register

Hi- Please reepair　

http://im33.gulfup.com/eKn1l.jpg

Last post : Re:vp-890	Reply: lxl
it is right. 512K x 16 (word)　or 1024K x 8 (byte)

All replies (1)

[ Posted:2013-10-20 03:46:17 ]

B58253

pepeoi

HI, yre you planning to add support for B58253 (SO8 - type) ?
Its commonly used in car ECUs as eeprom....
It wolud be perfect to be able to rewrite those!

Last post : Re:B58253	Reply: kruPL
=24C02

All replies (1)

[ Posted:2013-10-02 20:04:23 ]

VP990, LM75 support

kruPL

It"s possible add support National LM75 (read temperature and state overtemperature output pin) ?. The LM75 is standard sensor pc motherboards. Compatible chip - LM75A Philips, ADT75A(B) Analog, LM75DM33(MM50) ONSemi, LM75A Texas, MAX7500, TMP75 BurrBrown, G751-2 from GMT, NCT75-D OnSemi, MIC184 Micrel, TCN75 Microchip.
Datasheet:
http://courses.cs.tau.ac.il/embedded/docs/LPC2148_Education_Board/LM75.pdf
http://www.ti.com/lit/ds/symlink/lm75a.pdf

Last post : Re:VP990, LM75 support Reply: kruPL registered

OK. The LM75 is a chip without eeprom. I need test i2c chip interface (read ambient temperature via i2c interface from 16bit temperature register).

All replies (2)

[ Posted:2013-09-29 20:24:07 ]

WELLON reads but does not program

jonix39

Programmer soft updated need now, how to do? Upgrading the system to fail ....
No communication with Flasch / EEPROM
Windows sees WELLON. Self test ends successfully.
Reading memory is ok but the program does not work.
How to upgrade firmware?
Please help, job waiting.
Wellon vp 596

[ The message is modified by jonix39 ]

Last post : Re:WELLON reads but does not program	Reply: jin
When you upgrading the system failure, please catch a picture of your computer"s screen. The picture contain the information of your programmer and the failure.E-mail it to support@weilei.com.cn please.

All replies (1)

[ Posted:2013-10-09 20:09:19 ]

VP-890

aiman said register

Hi:plis add - s25FL064PIF - SOp(16), 300mil

Last post : Re:VP-890	Reply: myx1
please select S25FL064P *16SOIC

All replies (1)

[ Posted:2013-10-08 23:15:57 ]

blady

how to fix　run-time error 3049 Win xp

Reply the message

[ Posted:2013-10-07 03:47:44 ]

VP-280 GAL Issue - Crashes

Womble

I am trying to program a Lattice GAL16V8 or a GAL16V8A chip with my VP-280 on software version 4.3.4. When I hit Program it gets 10% into the programming and then the application and the burner crash. I have to manually kill the program process and reboot the burner. I used to be able to burn PALs using an earlier version of the program but I think the latest has a bug.

Can you confirm, and let me know where I could get an older version of the burner application from?

Last post : Re:VP-280 GAL Issue - Crashes Reply: lxl Host

maybe the VP-280 is bad

All replies (2)

[ Posted:2013-09-30 07:53:43 ]

Socket adapter for S29GL512N

mardyod

Hello.　I had a VP-890 and WL-TSOP56-F640.
S29GL512N available with WL-TSOP56-F640 or not.
Please answer me now.

Last post : Re:Socket adapter for S29GL512N	Reply: lxl
please contact with weilong@weilei.com.cn

All replies (3)

[ Posted:2013-09-27 15:06:16 ]

vp-990

paredes

I need to know if there is an adapter for the vp990 to be able to program the maxim ds2431x-s+ 1wire eeprom.

Last post : Re:vp-990	Reply: lxl
sorry,we can not find the socket from market

All replies (5)

[ Posted:2013-07-02 22:09:44 ]

vp-890

aiman said register

Hi:plis add - s25FL064PIF - SO(16), 300mil

Reply the message

[ Posted:2013-10-02 03:36:00 ]

Check sum

Nam Nguyen register

Hi, maybe just a dumb question, but hope you guy can help a selftaught　newbie. When I load a new file into buffer, I noted the checksum; then when I programmed into the device, VP290 said OK, but when I verify it said "FAIL". Also, when I read the device, the checksum is different. What did I do wrong ? could it be the device faulty ?
Any help would be appreciated.

Last post : Re:Check sum	Reply: lxl
chip type ?

All replies (1)

[ Posted:2013-09-25 17:20:03 ]

VP DEFECT

INJEMAR

Good morning!

  I need HELP!

After VP Software update can not do more reading, writing!!

Some information?

                   Thank you!

Last post : Re:VP DEFECT Reply: lxl Host

please send its photo.

All replies (1)

[ Posted:2013-09-24 19:53:07 ]

Download software

vellon user register

Hello, i wish to ask, why is your download so bad?? 4-5kb is download and later connection is broken, i cant download newer version of software, and each time when i try download connection is broken

Last post : Re:Download software	Reply: lxl
sorry,yesterday "download 1" is error, "download 2" is good. now, "download 1" and "download 2" are good. [ The message is modified by lxl ]

All replies (5)

[ Posted:2013-09-21 20:08:38 ]

Which software for VP498

wakeen1966 register

What is the best version to use with the VP498? I am asking because with version 4.63 I have been having problems with incomplete burns (primarily with Winbond 27c512).

Last post : Re:Which software for VP498	Reply: wakeen1966
I am using the AC adaptor.

All replies (2)

[ Posted:2013-09-16 22:34:03 ]

vp-498 programer faulty

bulent

i am using vp-498 programer

my problem

programfaulty ! 010F5C18150000F6

turkish message

>>Programlayıcı Arızalı!ID: 010F5C18150000F6

how my probelem resolve, thanks.

Last post : Re:vp-498 programer faulty Reply: bulent registered

sended

thanks

All replies (2)

[ Posted:2013-09-10 20:45:46 ]

how can i build my own mobile software

lupheryumang register

good day mates,..

im newbie here,...i just want to learn,..more in GsmSoftware..

how can i build my own mobile software? does anybody can help me..tnx and advance :)

Reply the message

[ Posted:2013-09-12 15:48:18 ]

Over Current - VP 190

Márcio

Hi ! I have some problems when I was programming my Eprom′s 29F040 - 70.Well, sometimes when I am programming(auto program) appear the message　OVER CURRENT DETECTED, but the process continue normally, what means this message ? Its a problem or not ?

Thanks a Lot

Last post : Re:Over Current - VP 190 Reply: lxl Host

plaese use AC adapter

All replies (1)

[ Posted:2013-09-12 02:30:59 ]

PLD Device Support

DaveH

hi, I have a VP880.

Can you tell me if I can read a MMI PAL16L8ACN with my programmer?

Thanks - Dave H.

Last post : Re:PLD Device Support Reply: lxl Host

sorry,can not.

All replies (1)

[ Posted:2013-09-10 23:40:18 ]

wellon vp-890

aiman said register

Hi:plis add - gm76c8128llfw85

Last post : Re:wellon vp-890	Reply: lcy
We have add GM76C8128, please download the latest software few days later. [ The message is modified by lcy ]

All replies (1)

[ Posted:2013-09-10 09:04:56 ]

AMIC A29040B-70F cannot erase

DevoDave

Windows 7
VP-590 Firmware 20
V4.6.2 program

Chip does not erase.　Tried Slow Program/Read.

----------------------------!

>>Man.Code:37　 Dev. Code:86
>>.Erase......
>>Erase OK!
>> 243.86Sec
----------------------------!

>>Man.Code:37　 Dev. Code:86
>>.Auto Program......
>>.Erase......
>>.Program......
>>Device Address:00000000H　Device Data:00H　Buffer Data:FFH
>>Auto Program fail!
>> 244.11Sec
----------------------------!

Last post : Re:AMIC A29040B-70F cannot erase Reply: DevoDave registered

New software erases the chip OK.
Many thanks (again!)
You guys give really good support.

All replies (6)

[ Posted:2013-09-02 13:36:18 ]

VP-880 GD25Q64B

eason

Hi
I have these machines "VP-280" "VP-480" "VP880"　
These machine can not write this SPI Flash "GD25Q64B"

Could you tell me this these machines can support this SPI Flash "GD25Q64B" ?

Best Regards

Last post : Re:VP-880 GD25Q64B Reply: lxl Host

Sorry, VP280/480/880 have stop produce. Its software have stop updated.
GD25Q64B is new chip.
Now VP996/596　support it.

All replies (1)

[ Posted:2013-09-05 11:23:33 ]

ttl/cmos test

Infirmier

Using vp-490 on windows7
Latest firmware and software version

When testing an ttl 74xxx,its NEVER found in autodevice
Then when testing,its always fail.
I use diffèrent ttl,all are NEW and have tested 25 of the same type.

Whats wrong?

Thanks

Last post : Re:ttl/cmos test Reply: Infirmier registered

not correctly inserted
i use two computers (one with new software(4.6.2) and the other one with old software (4.4.0) )
i programmed and tested enough chips to know how to insert it.so please dont tell me that i"m doing it wrong when i doing it right

All replies (17)

[ Posted:2013-08-26 03:56:32 ]

Over Current Detected

dshotka

Hello,

I am using the VP-290 to program an ATMEL ATF16V8BQL PLCC20 using the WL-PL20-U1 adapter. I can run a blank check, read, verify, but when I erase or program the device, I get an over current detection error warning. I have tried adjusting the Vcc and Vpp voltages but I still get this error. Any assistance is appreciated.

Last post : Re:Over Current Detected Reply: lxl Host

please download newest software.

All replies (1)

[ Posted:2013-08-31 00:32:46 ]

VP990, verify DS1287

kruPL

Hello, I have DS1287, VP990, fw19, soft 2013-08-08.
I can read, compare, but I can"t verify chip.
Sequence: read (ok), compare(ok), verify (fail)
>>.Verify......
>>Device Address:0000003FH　Device Data:00H　Buffer Address:0000003FH　Buffer Data:FFH
>>Verify fail!

Last post : Re:VP990, verify DS1287 Reply: myx1 registered

Uaually this series of chips like DSxxx or M48xxx are Real Time Clock plus RAM,with lithium energy source.
After AutoPrgoram is ok,read or verify again may cause the RAM data　 change.Cancel the Insertion Test is just avoided this situation.
So when Prgoram ok,do not chick others.use it on board.Check the board work or not.
But it must be sure the source files are right.Read from chip can not be reliable.

All replies (3)

[ Posted:2013-08-14 18:02:58 ]

pic16f628a

nkymk

hi, ı have wellon 490 programmer. ı　programmed pic16f628a. after programming verifying and comparing are ok. but when ı read the program in the pic, it seems it programmed just half of the bin dump and also it is complately different from the original dump.

[ The message is modified by nkymk ]

Last post : Re:pic16f628a	Reply: lxx
Please tell me you software Version. Which address can"t you read? Please send those pictures to our support Email.

All replies (1)

[ Posted:2013-08-17 23:45:44 ]

m27v160

paz123

I have vp 390 but this chip m27v160 I cant copy file onto eeprom the programmer vp 390 says man code0.0 dev code 0.0 please help

Last post : Re:m27v160	Reply: jin
Please add the adapter power when you write the chip.

All replies (1)

[ Posted:2013-08-15 20:07:40 ]

NEC D78F0828B support

ssilvviu

Hi!
I have a VP890.
Could you add support for NEC D78F0828B processor?

Last post : Re:NEC D78F0828B support	Reply: lcy
We have support UPD78F0828B, please download the latest software. [ The message is modified by lcy ]

All replies (4)

[ Posted:2010-01-16 06:54:59 ]

can i use vp290 software for vp280

vik

can i use vp290 software for vp280 programmer　and there is no vp280 software set up on wellon website. plz rply

Last post : Re:can i use vp290 software for vp280	Reply: lxx
You can use 4.3.4 Ver.

All replies (1)

[ Posted:2013-08-14 18:35:56 ]

vp-490

revlon

pls help how to add　support the HY27US08561A?

Last post : Re:vp-490	Reply: lxl
VP-490 do not support HY27US08561A.VP-990/GP400 support HY27US08561A.

All replies (4)

[ Posted:2013-08-09 20:18:13 ]

communication error!

terrapigui register

last week bought a gp20. My first surprise is that it came with the power switch backwards, I mean when the switch was on, the programmer is off and when the switch is off, the programmer is encendido.bueno, this defect is not very important, but my problem is that after installing the software I can not read or write or delete any device because it gives me the message "communication errors"
the programmer is conected and selftest is ok

[ The message is modified by terrapigui ]

Last post : Re:communication error!	Reply: lxl
please email its picture to us

All replies (1)

[ Posted:2013-08-12 18:24:12 ]

TH58NVG5T2ETA00 toshiba

specialmio register

hi , what programmer read this eprom ?

Last post : Re:TH58NVG5T2ETA00 toshiba	Reply: lxx
Chip memory is too large, the programming time required is too long. We can provide custom software to the chip.

All replies (4)

[ Posted:2013-08-05 22:53:53 ]

hello

revlon

hello　 i want to buy the　vp-590 it is supported the hynix HY27US08561A *48TS?　i have an adapter like this

http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=3102

Last post : Re:hello	Reply: lxx
GP-10 support HY27US08561A.

All replies (4)

[ Posted:2013-08-06 20:50:49 ]

M30624FGPFP

jagdeepdhillon register

Dear Sir,

i am trying to read and program M30624FGPFP from isp port with VP-990 . i am facing problems as under:-
1.　 MY VP-990 GOT HANGED FOR SOME TIME AND SAY"S NEED AC ADAPTER, EVEN IT IS CONNECTED.
2.　 MY SOFTWARE GET CORRUPTED AND I AM UNABLE TO SELECT ANY CHIP. I AM USING VER. 4.6.2 WITH FIRMWARE 19.0

Please advice me, what i can do in that case.
thanks

Reply the message

[ Posted:2013-08-05 21:33:28 ]

VP-890

aiman said register

Hi:plis add - HY27US8121B

Last post : Re:VP-890	Reply: lxl
maybe its type is HY27US08121B.VP-890 have support. [ The message is modified by lxl ]

All replies (1)

[ Posted:2013-07-25 07:52:52 ]

ST M95040-W

benaknoun

Hi
I want to read / program this chip.
On device selection of my VP990, there is M95040-W, and this device info on software says 300mil, but datasheet is 150mil.
And M95040-W *8SO says it needs an adapter WL-SOP8-U001.

I am confused which one to select?
And M95040-W does not need adapter?
Thanks

Last post : Re:ST M95040-W Reply: lxl Host

please email to weilong@weilei.com.cn

All replies (5)

[ Posted:2013-07-16 21:26:06 ]

Please add Pics

kyo

Hello!! Please add pics pic12f1840 and pic16f1526 in Vp590. Best regards, Thank you!

Reply the message

[ Posted:2013-07-23 01:17:52 ]

W25X32VSIB

lelobq

may include W25X32VSIB

Last post : Re:W25X32VSIB	Reply: kruPL
Windbond top side marking ... If you have W25X32VSIB ( maybe W25X32VSIG ?) then chip W25X32VSSIG. Please select W25X32V* , sop8 package.　Works?.

All replies (1)

[ Posted:2013-07-19 04:14:48 ]

VP990, read W25X16AVSIG

kruPL

Hello.
I try read W25X16AVSIG
When software 2013-02-20,fw19
>>.Verify......
>>Device Address:0018FFFCH　Device Data:FFH　Buffer Address:0018FFFCH　Buffer Data:00H
>>Verify fail
I install other version software.Read result:(total commader md5 file )
349a63679e9dc634f2f2d5c89fd40491 *W25X16_4.5.1(2012-11-07).bin
9d930336fe6b9d78002669162bc48fed *W25X16_4.6.1(2013-02-20).bin
81aa11f46ea003bdcd486a612d34e62d *W25X16_4.6.2(12-7-2013).bin
W25X16 algorithm changed/improved?.

[ The message is modified by kruPL ]

Last post : Re:VP990, read W25X16AVSIG	Reply: kruPL
I have test on other programmers (thanks my friends). VP790 + 4.6.2 (2013-06-18) fw 19 -> read ok UPA v3 build 0.14 read as 25VF016B -> read ok! Labprog+ -> read ID - fail, test canceled SPIFlash -> read ok Finally test on my VP990: erase, programm, verify, compare . Soft 4.6.2 2013-07-11 is ok. Thanks. [ The message is modified by kruPL ]

All replies (4)

[ Posted:2013-07-14 18:35:17 ]

VP-890

aiman said register

Hi:plis add - MICROCHIP SST39VF3202 *48TS

Last post : Re:VP-890	Reply: lxl
please select SST　SST39VF3202 *48TS

All replies (1)

[ Posted:2013-07-19 10:56:48 ]

VP-890

aiman said register

Hi:plis add -cFeon EN29LV040A *32TS

Last post : Re:VP-890	Reply: lxx
We have add it.Please download new software in a few day.

All replies (1)

[ Posted:2013-07-16 23:05:02 ]

VP890

aiman said register

Hi:plis add - H27U2G8F2CTR

Last post : Re:VP890	Reply: myx1
pleas download new soft

All replies (6)

[ Posted:2013-07-10 07:44:41 ]

STC Microcontroller

vkmicrosystems register

A lot of STC make microcontroller like STC10Fxx are not supported in Wellon GP-20.Are you going to implement these microcontroller with GP-20?

Last post :

Re:ST62T25C

Reply: RobM90 registered

Thanks I could program three mcu"s, but to get it, I had to program many times each one. Other detail, I can"t protect the device with bit protection, since doing so the device is damaged.

I tried to program the device in two steps, first the file source and then the bit protection, but I had no success and I don"t know if this is possible in OTP device.

Regards

All replies (8)

[ Posted:2013-07-04 02:54:31 ]

VP-990 H27U2G8F2CTR-BI help

lelobq

need to dump the chip H27U2G8F2CTR-BI but Wellon software has no way selected, I need urgent help. My programmer is VP-990

[ The message is modified by lelobq ]

Reply the message

[ Posted:2013-07-09 19:14:24 ]

VP-390

hexxx309

I am using the VP-390, but it"s not working well.
I plugged in the programmer and then open the software. Then the following message pops up. I followed the instructions and reconnected the USB port or even reboot my computer for many times. It just happened to succeed once. The next time, it fails again.
That time it was able to connect, the programmer can only read from the chip but failed to write. I am setting the chip model correctly, because that"s what I use in VP-20.

Last post : Re:VP-390	Reply: hexxx309
Hi, I fixed the problem by using the 32bit version software, although I am using 64bit win7. THX

All replies (3)

[ Posted:2013-06-28 23:05:10 ]

vp-590 at17lv002a

scmoon

Hi,I have test using SW 6.4.2 updated 4/7/2013 to write reset polarity. But it don"t work as well as previous version. let me know how to write AT17LV002A reset ploarity !

Reply the message

[ Posted:2013-07-04 15:26:28 ]

V890

erika

Hi, I have a s29gl032N90ffis2 programmed and locked. I need erase it. It′s possible ?
How to read the configuration bits prevent the delete.
How to clear it.

Last post : Re:V890	Reply: jin
This chip has a secured silicon sector which has 128 words. The 128 words are OTP, can"t be erased. You can read the 128 words, and they are in buffer address 400000H---4000ffH. Except the OTP sector, you can erase the chip normally.

All replies (1)

[ Posted:2013-07-03 10:21:12 ]

Total 1464,Total 30 pages

[<<][16][>>]

search: title content user

Web homepage | Contact us | About us

Tianjin Weilei Technology Ltd.

296.88 ms