Tianjin Weilei Technology Ltd.

Homepage:Login:Register:Soul:Top Host

Forum style

Interface Style:

Total 1465,Total 30 pages

[<<][27][>>]

Programming MicroChip PIC 24F micros

stephr1

I have a VP-480. Can the VP-480 program MicroChip PIC24F series microprocessors? Can I change parameters to make it work? Shih shih...Steph

Last post : Re:Programming MicroChip PIC 24F micros	Reply: lxx
VP-480 can not support PIC24F series microprocessors. You can not change parameters to make it work.

All replies (1)

[ Posted:2010-02-04 02:44:54 ]

Need help onTesting LM339.

razara

[color=#0000FF]Hi
I need support for testing LM339. I did try many many times but always got the message Test Fail cause of the expected and the actual different. I did create the TEST PATTERN for LM339 but no success, as the result always shows the Vcc as low instead of HIGH. Please help.[/color]

Last post : Re:Need help onTesting LM339.	Reply: lxx
VP-380 can not support LM339. We had remove it from our list. If you want test it, you can move it up two cells, as a 18-pin device is re-editing test. V0001 HHV0101XXXX0101GHH V0002 HHV0101XXXX0110GLH

All replies (3)

[ Posted:2010-02-02 02:05:40 ]

pic16f72

karrom

I read the chip pic16f72 (28 pin) with vp-880
and save the file .
and program another chip (16f72) to file.
chik blank ok
erase ok
program ok
compare ok
but the chip (16f72) don,t work in pourd...
i use many chip same problem i don,t
anderstand reason (the problem) ......
please help me
how i can read　pic16f72 (28 pin)Correctly
or program it Correctly....
thank you....

Last post : Re:pic16f72	Reply: gxj
The chip which work OK in pourd is secured,so you can not read out the right data.You should look for the source file of PIC16F72. [ The message is modified by gxj ]

All replies (6)

[ Posted:2010-02-01 15:50:44 ]

VP-280 stopped working

Pinasco

Hi,
My programmer worked very good until a few days ago when I began getting errors in programming devices. I programmed devices on another programmer and they were good.
In self-test:
Pin 23 Input is High, VPP output is high.
Pin 5 Input is High, VPP output is high. etc etc...
At the end almost all pin are yellow and fail the test, only pin 1,2,3,4,6,7,8,10,20,22,23,41,42,43,45,47,48 are white. Pin 18 and 28 are red
I can fix it myself? otherwise I can send it for repair?
Thanks a lot

Last post :

Re:VP-280 stopped working

Reply: Pinasco registered

mail with picture sended

Roberto

All replies (2)

[ Posted:2010-01-30 06:19:24 ]

big flash problem

babay

I"ve found out that vp-880 which has to support k9k8g 8Gb flash CAN NOT work it properly. Should be th bug of the software. I guess it simply can"t alocate the read buffer of size more than 1 Gb. Also there is very buggy algorithm of writing spi flash rom(tasted a lot of different models e.g. 25x080 and so on.) - errors on　writing.

Last post : Re:big flash problem	Reply: cm
Do you contact the adapter power?if not,please link it.When you programme 25x80,please modify the Vcc from 3.0V to 2.5V.

All replies (1)

[ Posted:2010-02-01 01:44:54 ]

atmega44 ISP without adapter HELP!

nexton

Hi
I have VP-190, I need schema for connecting atmega162 (16au, 44 pins) ISP to 40pin ZIF socket on VP-190 programmer.
Is this schema correct:

http://img37.imageshack.us/img37/7749/44isp.jpg
(I don"t have adapter)

Also Version 4.3.0(19.1.2010) doesn"t have VP-190 as programmer in selection of programmers? Which one I need to select use?

Thanks

Last post : Re:atmega44 ISP without adapter HELP! Reply: cm registered

If the chip pin is the same as the PDIP pin.You can programme it with an adapter.

All replies (10)

[ Posted:2010-01-23 21:52:12 ]

vp890 and altera ep600idc

pippo

Hello i have buyed a vp 890, the　altera ep600idc is supported by programmer.Can add support for Dallas I button whit adapter.Thanks

Last post : Re:vp890 and altera ep600idc	Reply: cm
All of our programmer can"t support ep600idc.We need the programme informaiton.

All replies (1)

[ Posted:2010-02-01 21:09:19 ]

Testing LM339

razara

Hi, I have VP380 and in the IC TEST, the test for LM339 fails always. The result shows that the Vcc is always LOW instead of HIGH. I created the pattern mysely but still the same problem. Can you help me on this. I have installed the latedt updated software for VP380.

Reply the message

[ Posted:2010-01-30 20:36:21 ]

support for 6167 RAM on VP-880

Sivaraj

We have VP-880 programmer.Could you please add support for testing the RAM IC type 6167

Last post : Re:support for 6167 RAM on VP-880	Reply: lcy
We have modify our software, please download the latest software several days later and then select cy7c167a to test. [ The message is modified by lcy ]

All replies (3)

[ Posted:2010-01-19 09:39:02 ]

MC68HC11KA4

ssilvviu

Could you add support for MC68HC11KA4?
I have a VP980.

Last post : Re:MC68HC11KA4	Reply: lxl
VP-980 have been stopped produce

All replies (5)

[ Posted:2010-01-21 00:55:08 ]

CY7C65113C and VP-880

kisslorand register

I have VP-880 and I have to program CY7C65113C. In the device list of VP-880 I can see only CY7C65113. Can you please add support for CY7C65113C also on VP-880? Thx

Last post : Re:CY7C65113C and VP-880	Reply: kisslorand
I did that but SW gives me error "Programming failed". Device is still blank. I programmed the device with Labtool 48UXP without any problem.

All replies (2)

[ Posted:2010-01-07 17:00:23 ]

memory eprom

HugoMoreno register

HI, I´m working with old technology. I would like to know if it´s posible to work with M27C256B (eprom memory) Thanks for your help

Last post : Re:memory eprom	Reply: cm
The programmer VP-590,VP-790,VP-990,GP-10,GP-20 can support this chip.

All replies (1)

[ Posted:2010-01-05 22:08:31 ]

Wellon VP-280

vwphun

Hi,

can you add support for 44pin PSOP AM29FX00 flash memory in VP-280? thanks

Last post : Re:Wellon VP-280 Reply: lxl Host

Sorry, VP-280 can not support it.

All replies (1)

[ Posted:2009-12-30 23:38:47 ]

Driver

barteklabe register

Hi
I need drivers for vista 64 bit, where can I find it?
or You should make driver for vista 64 bit

[ The message is modified by barteklabe ]

Last post : Re:Driver	Reply: lxx
Now you can download 64 bit test software from our web.

All replies (13)

[ Posted:2009-10-25 17:35:37 ]

attiny12

ninoumouad register

Hi, i want to reprogram a attiny12 for my labtool , i want to know if is possible ot not .

Last post : Re:attiny12	Reply: cm
Labtool isn"t our production.

All replies (1)

[ Posted:2009-12-07 04:22:35 ]

AM2764ADC Over Current Detected

Womble

I have some AM2764ADC chips that will not program with my VP280, I get "over current detected" when I try to program. I have some AM2764 chips that program perfectly. Is this a bug with the specifications for the 2764ADC chips?

Thanks

David

Last post : Re:AM2764ADC Over Current Detected Reply: lxl Host

maybe,now,these chips is all eld chip.

All replies (3)

[ Posted:2009-12-05 20:25:56 ]

problem with vp890

karrom

I have 2 Programmer vp890 and vp880
When I write sst25vf016b with vp880 (ereas.. ok/program..ok/veryfly..ok)..Working on board(no problem it good)...but When I write　with vp890 just (auto program..ok) .It does not work on the Board (ver.4.2.0)and vp890 Lose connection to my computer and Nor would connect to the computer, but i select any chip And close the program...Problem only in this type sst2vf016b .please new softwe..thanks.

Last post : Re:problem with vp890	Reply: lxl
send to your seller

All replies (21)

[ Posted:2009-11-20 14:08:15 ]

will this read hm628128alp-7

Dean

I have a sram chip I want to read/modify and I was wondering if you could help it is a hm628128alp-7 and is piggy backed on a ds1216 chip for the battery
backup
will this programmer/software do this?

Last post : Re:will this read hm628128alp-7	Reply: jin
We can only test the chip hm628128alp-7,but can"t read/modify it. We didn"t support ds1216.

All replies (2)

[ Posted:2009-11-29 05:05:42 ]

Pal plds

chiptron

Could somebody please check that vp-280 is burning and reading pal plds correctly.
PALCE16V8H
i am getting different results reading on different software verions
i have burnt and read some to check this.
this makes it impossible to know if i am getting a good result reading a chip where i do not have original files.
What should i see on 280 if chips where protected.
thanks.

Last post : Re:Pal plds	Reply: chiptron
Thanks

All replies (4)

[ Posted:2009-11-13 02:02:39 ]

VP-280 trouble

Jotunn

Hi,
during start of software there is a message:

Programmer initializing failure. Possible causes:
1. There are devices on the Socket
2. The programmer"s some function is disable!
Device program maybe fail.

System Windows 7 (build 7100) 32bit
Software 4.2.0 (17.11.09)
Power adapter plugged in.

After ignoring I got some functionality:
93c86 - i can read, erase, but writing fails after 31 seconds
EEPROMs are ok for sure.
I have tried reinstalling - no luck.

Last post : Re:VP-280 trouble Reply: cm registered

Please click the "test"menu,and select the last item "Self_test".You can test the programmer.

All replies (5)

[ Posted:2009-11-20 07:16:35 ]

Win 7 / 64 Bit

masto

Hi,i upgraded my PC to Win 7 64 bit, but now i cannot install the driver anymore. When will yo have a driver ready for this?

[ The message is modified by masto ]

Last post : Re:Win 7 / 64 Bit	Reply: lxx
Sorry, we can not support 64 bit system now.

All replies (1)

[ Posted:2009-11-22 18:50:15 ]

read samsung K9F5608U0B

oem repair register

hello,

Last post : Re:read samsung K9F5608U0B	Reply: lxl
VP-980 have Stop production.VP-980 is slower.when read it. VP-890 only need 78 sec. when read K9F5608U0B

All replies (3)

[ Posted:2009-11-23 00:12:36 ]

atmega128

barteklabe register

hi
can I program atmega128 TQFP64 ?
vp990

[ The message is modified by barteklabe ]

Last post : Re:atmega128	Reply: cm
Our programmer VP-990 can support this chip.You need an adapter to programme this chip.

All replies (3)

[ Posted:2009-11-18 22:47:42 ]

25L800EM2C

barteklabe register

hello
I have vp990
can I program 25L800EM2C ?? if not please add this chip

Last post : Re:25L800EM2C	Reply: cm
The programmer VP-990 can support MX25L8005.

All replies (3)

[ Posted:2009-11-18 22:42:18 ]

VP-490 m27c322 programming failed

hemvlett

Hello, i"ve got a problem when i"m trying to program a 27c322. Everytime i"m trying i"ve got this kind of error message: >>.Auto Program......
>>.Blank Check......
>>Device Address:00000000H　Device Data:B500H　Buffer Data:B547H
>>Auto Program fail!
>> 31,28Sec　　　 I tryed more than 10 differents 27c322 eprom and the programmer always failed... I have successfuly programmed others eprom like 27c512, 27c256...　Thanks.

[ The message is modified by hemvlett ]

Last post : Re:VP-490 m27c322 programming failed	Reply: hemvlett
YES ! it works fine with the new soft version !!!! Many many thanks for your great support!

All replies (15)

[ Posted:2009-10-23 04:03:54 ]

MC68705P3S

chiptron

Is their any possibility the vp-280 can support this 8-Bit EPROM Microcomputer Unit.
Also why no 82s131 support ?

Last post : Re:MC68705P3S	Reply: lxx
We have not its programming algorithm, so we can not support it.

All replies (1)

[ Posted:2009-11-09 20:01:30 ]

AMD 27C100s Wont Program on VP280

Womble

My VP-280 can"t program AMD 27C100 chips, I have 6 chips, from 3 different sources, all pass the blank test, then instantly fail the write test

>>.Program......
>>Device Address:000000H　Device Data:FFH　Buffer Address:000000H　Buffer Data:F3H
>>Program fail!
>> 1.95Sec
----------------------------!

BUT after this fail the chip passes the blank test again.

I am running Ver.: 4.2.0(23/10/2009) software.

Can you help?

Thanks

David

Last post : Re:AMD 27C100s Wont Program on VP280 Reply: Womble registered

Many many thanks!
It works now!

All replies (4)

[ Posted:2009-11-03 12:09:21 ]

Before i decide to buy...

Przemyslaw register

Hello

I sold my wellen programmer because it didn`t support gal 22v10 - nevertheless You declared it did.　
!!!

Now, i want buy v280 -- so my question is :

- will it support 22v10
- AM 29f040 ??
- 29f010 ?

regards, lotharek

Last post : Re:Before i decide to buy... Reply: Boz registered

I have a VP-590, it programs GAL20v10 perfect.

All replies (2)

[ Posted:2009-11-06 01:43:19 ]

28f640j3c120

barteklabe register

hi
please add this chip 28f640j3c120 BGA 64

[ The message is modified by barteklabe ]

Last post : Re:28f640j3c120	Reply: barteklabe
ok I find it :) my programmer support it

All replies (3)

[ Posted:2009-11-05 07:36:29 ]

Windows 7, 64 bit driver

TroyAus

Just wondering if you have an approximate date for when a windows 64 bit driver will be made available. As I like using Wellon programmers but i have upgraded to windows 7 64 bit.

Last post : Re:Windows 7, 64 bit driver	Reply: cm
I am sorry,we can"t tell you an approximate date.I can say,we will support it as soon as possible.

All replies (1)

[ Posted:2009-11-01 10:57:36 ]

scanvec

hi, i have an VP-38+; how i do to update her for AMD29F200 AND　AMD29F400

Last post : Re:scanvec	Reply: cm
The software of VP-38+ have stoped production.The last version is 3.9.7.If you can"t find this chip in the software,the programmer can"t support this chip.

All replies (1)

[ Posted:2009-11-01 08:02:41 ]

ATtiny 12

karrom

hi ...i have chip ATtiny 12 ( 8pin ) i want to program it.erase ok.program ok. but the data in the chip still the old data.i cant program it with new data.and also i cant erase the old data .please till me what can i do?.........thanks

Last post : Re:ATtiny 12	Reply: TroyAus
Remember ATtiny 12 doesn"t support GCC so your code needs to be written in assembly language before compiling. If you don"t like Assembly stick to ATtiny45 or ATtiny 85.

All replies (4)

[ Posted:2009-05-21 06:12:22 ]

VP980 K9GAG08U0M

krisszmix

Hallo ! The K9GAG08U0M, it"s avaliable added the VP980 program support ? Thanks..

Last post : Re:VP980 K9GAG08U0M	Reply: jin
This chip"storage is too big to add in VP-980 programmer. It will spend too much time to program and may be failed. So it can"t be add in VP-980.

All replies (1)

[ Posted:2009-10-29 05:40:12 ]

Windows 7

Womble

Does your software work with Windows 7 (32 bit and 64 bit)?

Last post : Re:Windows 7	Reply: cm
Now,we have test the software in 64 bit operation system.I think we will support it in the future.

All replies (1)

[ Posted:2009-10-26 08:41:00 ]

Can"t access PIC"s from select menu

deuce

I anm using ISP1 programmer. Whenever I try to select a MPU the only option is ATMEL. I want to program a PIC18F2525. Now I know that is in Module15 so I used the ISP1 Control software to write that. But nothing changes and I still only get ATMEL not PIC.If I use the ISPconfig to read the ISP1 it always says Module9 even after writing Module15 to the ISP1. Help! What am I doing wrong? I have tried the programs (and ISP1) on a VISTAx64 and a win2000 PC with no success.

Last post : Re:Can	Reply: cm
You need buy the new module.Please contact our supporter,and tell him programmer information.

All replies (1)

[ Posted:2009-10-25 06:54:15 ]

VP-ISP 1 and 25x80A VSIG - write problem

woxy

I"m having problems with 25x80AVSIG chip. Reading OK, Erasing OK, Write Failed: Device buffer: FF, File Buffer: 61.
It seems that nothing is writing.
I"ve found info that someone programmed this family chip setting the "Invert SCLK" option in PonyProg software.
In Yours there is no such options for Fuse BITs or so, I think that would be a very useful thing to be able to work on BIT"s.

Last post : Re:	Reply: cm
About the buffer size,in our software,we add 16 byte to save config.So,when you save the file,the buffer size is 16 byte more than the original file.This operation will not break your original file.

All replies (9)

[ Posted:2009-10-10 04:15:18 ]

Fujitsu MBM 2716

Bingovit

I"m having some troubles programming a Fujitsu MBM2716 chip.
I"ve tried programming it with the generic 2716 and it says it"s OK. But when plugged in my PCB it ain"t working!
The file is 100% good which I want to put on it, I"ve tried several MBM2716"s.

I"m using a VP-480, can the MBM2716 by Fujitsu added to the list please?

Thanks,

Evert

Last post : Re:Fujitsu MBM 2716 Reply: lxl Host

1.this type chip is elder chip.many is badly.
2.please download new soft.

All replies (3)

[ Posted:2009-10-16 23:20:19 ]

Byass security sequence MC68HC908

ssilvviu

Hi!
I have a Wellon 980 programmer and I"m trying to read a freescale MC98HC908 MCU with a 8 bit security sequence.
Could you add an update that can bypass that sequence?

Last post : Re:Byass security sequence MC68HC908	Reply: cm
No,we can"t supply any security sequence.

All replies (3)

[ Posted:2009-09-17 04:08:16 ]

esmt f25l008a and atmel 26DF081A

barteklabe register

hello
please add this chip in standard dip8 package
line"s on the package:
1"st line: ESMT 50
2"nd line: F25L008A
3"rd line: C70AF
4 line　 : 0743

when I select this chip from library (in SOP package) I can"t program it.
and

add atmel 25df081a in all package :)

[ The message is modified by barteklabe ]

Last post : Re:esmt f25l008a and atmel 26DF081A	Reply: cm
The programmer VP-990 can support F25L008A.If you can"t programme it,please tell me information in details.Besides,VP-990 can support 25DF081,we will support it in the future.But,if you want test it.You can select AT26DF081,and programme 25DF081.If the result is OK,please tell me!Thank you!

All replies (3)

[ Posted:2009-10-12 03:23:52 ]

spansion

qaz

hi i can read and erase spansion s29jl032h90tf131 no problem but when i try write i get errors i have a 480 modle any help please.

Last post : Re:spansion	Reply: cm
Did you link the power adapter?If no,please link it.

All replies (1)

[ Posted:2009-10-04 03:46:02 ]

VP980 - PCF7947AT

ssilvviu

Could you add PCF7947AT?

[ The message is modified by ssilvviu ]

Last post : Re:VP980 - PCF7947AT	Reply: lxx
We do not find its datasheet and we do not know if it need to be programmed.

All replies (1)

[ Posted:2009-09-26 16:40:52 ]

vp980 - 40257

Fastah

Please add testing cmos chip cd40257 on vp980

thank you

Last post : Re:vp980 - 40257 Reply: lxx registered

Plz send me 4464 ,44256 and 511000 datasheet.

All replies (5)

[ Posted:2009-09-20 03:23:48 ]

vp980 - cd4007 testing

Fastah

Hi
I just repairing some old scope and suspect one cd4007 was failed but testing with vp-980 say chip was ok. Is this test realy reliable and complete? I don"t have spare chip for trying. Can you recheck testing options for this chip in software?

Thank you

Last post : Re:vp980 - cd4007 testing Reply: Fastah registered

About testing dram chips... this is basic five type of dram chips:
4164 (64k x 1bit), 4464 (64k x 4bit), 41256 (256k x 1bit), 44256 (256k x 4bit) and 511000 (1M x 1bit)... if you make some "generic" algorithm for testing various manufacturers and speeds this will be great feature... Please see what you can do... I have 5-6 datasheets and can send all to your mail....
Thanks again

All replies (3)

[ Posted:2009-09-22 07:44:54 ]

support for pic16f676

bytek

Hi,
　　 Can any one tell me ,if vp190 is supporting pic16f676

Last post : Re:support for pic16f676	Reply: lxx
VP190 don"t support pic16f676.

All replies (1)

[ Posted:2009-09-17 23:19:22 ]

Latest program

stephr1

I just tried downloading the latest 9/16/2009 software (.zip and .exe) and I get checksum　or corrupt errors.

Last post : Re:Latest program	Reply: gxj
There are something wrong with our network yesterday,so please download the software today.

All replies (1)

[ Posted:2009-09-17 07:00:46 ]

ST 25P80VG

barteklabe register

Hi
please add this chip ST 25P80VG
thanks

Last post : Re:ST 25P80VG	Reply: cm
The programmer VP-990,VP-790,VP-590,VP-380 and VP-280 can support 25P80

All replies (1)

[ Posted:2009-09-15 00:00:08 ]

S29GL032N-TF-04

Karrom

I have chip S29GL032N90TF104　48PIN　1. read ok　2. erase ok　3. programing fail -try many chips the same . i select option "slow program/Read" ,same problem ...please help　.i have 980 and 880 programer.

Last post : Re:S29GL032N-TF-04	Reply: karrom
thank for you .its ok program.

All replies (2)

[ Posted:2009-09-04 11:42:02 ]

Config window

kisslorand register

On config window the text on the dropdown list not fully visible. See for example Atmel MCU"s or PIC"s.

Last post : Re:Config window	Reply: kisslorand
Still fuzzy at Atmel MCUs

All replies (10)

[ Posted:2009-08-03 16:15:03 ]

VP-980 support

Fastah

Please add support for testing dram chips 4164 and 41256 series like:
Samsung KM4164A-15, KM4164B-15, OKI M3764-15, Inmos IMS2600P-15, OKI M41256-15, Samsung KM41256P-8...
I"m try testing correct chips with select Panasonic MN4164 but allways report error on various type of dram chip.
Is possible testing 4116 dram chips?
I"m old computer collector and repairer and every day must testing various vintage ram chips.
VP-980 works fine and I"m very glad with this programmer.
Thank you

Reply the message

[ Posted:2009-09-07 01:17:09 ]

recomend what model and low cost

davidkoh

dear sir,　I am trying to look for lost cost program but works wonder. i use to copy 27v322 is 3.3 v　and 160v . i need to protech them been copy by others and other eprom model . I also looking for compact flash card　that even copy the protect hiden file. Do you have any such device programer.　Urgent require. thanks

Last post : Re:recomend what model and low cost	Reply: cm
VP-590,VP-790,VP-990 can support 27V322.About other chip,please tell me the chip name.

All replies (1)

[ Posted:2009-08-22 22:09:27 ]

Total 1465,Total 30 pages

[<<][27][>>]

search: title content user

Web homepage | Contact us | About us

Tianjin Weilei Technology Ltd.

203.13 ms