Tianjin Weilei Technology Ltd.

Homepage:Login:Register:Soul:Top Host

Forum style

Interface Style:

Total 1464,Total 30 pages

[<<][20][>>]

AT90S1200 fuse settings

Fastah

I found bug in software. When select AT90S1200, Config screen, fuse settings popup SPIEN RCEN is too narrow... can"t read RCEN option is enabled or disabled.

Please correct this.

Thank you

[ The message is modified by Fastah ]

Last post :

Re:AT90S1200 fuse settings

Reply: Fastah registered

Now working...

Thank you

All replies (4)

[ Posted:2012-07-25 04:43:10 ]

CY7C293A blank check on VP980

Fastah

Hi
I found bug in software (latest and older). When Blank check on blank eprom CY7C293A program say:

>>.Blank Check......
>>Device Address:00000000H　Device Data:FFH　Buffer Address:00000000H　Buffer Data:FFH
>>Blank Check fail!
>> 0,02Sec
----------------------------!

Chip was realy blank, program read all FF and checksum is 0007F800
Please correct this.

Thank you

Last post : Re:CY7C293A blank check on VP980 Reply: Fastah registered

Hi
Now everything works fine...
Thank you

All replies (15)

[ Posted:2012-07-25 04:35:23 ]

VP-190 Confusion....

marc.hull

Sirs.

Please help with a couple of issues.

1) Your documentation states that the VP-190 can test DRAM and SRAM but I cannot find a way to do this.　The DRAM/SRAM button is inactive. How can it be done ?

2) When testing 14 pin logic chips there is a pop up on the software stating some pins need to be jumperd.　The text states that these are pins 31 and 32 but the picture shows pins 27 and 28 highlighted.　 So which is it　?

Last post : Re:VP-190 Confusion.... Reply: cm registered

Hello!
The programmer VP-190 is only sell in China.So there is not instroduction in the web. You can download the newest software in English. The software can distinguish the programmer automacticlly.
About jumper, we have modify the software, we modify the demo picture in the software,but when the user test them, you also need jumper as the software.

All replies (3)

[ Posted:2012-07-29 10:16:21 ]

vp-590

Marcos

vp-590 windowns does not recognize the drive
Error after system update, what to do

Last post : Re:vp-590	Reply: lark
Please enter WELLON software, click ‘Help’->’Contents’, read chapter3.7 Error message ,’ If your programmer that had the function of update online lost its program, you can resume it’, do as what follows.

All replies (1)

[ Posted:2012-08-03 05:55:14 ]

VP-990

farhad

Hi. your new software dos not work for test uln2001,2,3 ...uln2803,4.... and maybe other devises !! this is really not good for you and your software team　!!!!!

Last post : Re:VP-990	Reply: lxl
please download new soft.

All replies (1)

[ Posted:2012-08-01 04:49:09 ]

wellon vp -380

bharat

when i select the ic name (w39v040fapz) it shows w39v040fap*32 pl
or 32ps
what is the difference between these two

Last post : Re:wellon vp -380	Reply: lxl
w39v040fapz is lead free.

All replies (1)

[ Posted:2012-08-01 17:11:00 ]

Vp-390 not working after failed update

zige

Hi.

My vp-390 no longer works after a failed system update.
I get no lights and when plugged in to my computer it says usb device bot recognized. Is there a way to recover from a failed update? If not would I be able to send this in for repair?

Thanks

Last post : Re:Vp-390 not working Reply: hlark registered

Please enter WELLON software, click ‘Help’->’Contents’, read chapter3.7 Error message ,’ If your programmer that had the function of update online lost its program, you can resume it’, do as what follows.

All replies (1)

[ Posted:2012-07-30 17:55:22 ]

VP-390 Need update for PSOP44

M.Y.Perf

Hello i have just buy a wellon VP-390
and they didn"t work with the psop44 ( AM29F400BT)
they say my it"s a 48pin but it"s a 44pin
please help me
thanks

Last post : Re:VP-390 Need update for PSOP44	Reply: lxl
VP-390 only support TSOP48 package,do not support PSOP44 package.

All replies (1)

[ Posted:2012-07-30 22:34:24 ]

29F400BC support and adapter question

benaknoun

Hi
I have the VP990 programmer
I would like to read this chip:
F Malaysia 29F400BC-70-Y
Does it support this chip? because i can"t see the name of manufacturer in list
Which adapter do i need for this chip?

Thanks

http://i1152.photobucket.com/albums/p496/appleaccessories/IMG_5346Medium.jpg

Last post : Re:29F400BC support and adapter question Reply: jin registered

Your programmer update failed. Please do the "system update" one more times. Please click "Help"-->"system update" and then according to the notice step by step.

All replies (11)

[ Posted:2012-07-01 08:38:49 ]

Buffer - new functions

kruPL

I"m user VP-990 programmer.
I want dump the contents of my buffer to plain txt file　(not via pdf creator, files converter etc.).
Example (address, data, ascii)
000000　 00 00 00 00 78 21 E0 1C 18 1E 00 00 00 00 00 00　....x!Ó.........
Is it possible to add function:
*direct dump buffer to notepad or clipboard or txt file
*GoTo address in BufferEditor　?.

[ The message is modified by kruPL ]

Last post : Re:Buffer - new functions	Reply: kruPL
I"ve found a solution. I use Generic/TextOnly printer (page size 285*285mm). Now I can go to the Editor, and print on virtual text printer (save to text file).

All replies (2)

[ Posted:2012-07-25 20:12:35 ]

VP-280

Roy

I noticed the Mfg and Device ID values are not read correctly when I use my VP-280 with a SST 39SF040-70-4C-PHE.

Last post : Re:VP-280	Reply: jin
You can change another chip to try.

All replies (1)

[ Posted:2012-07-21 00:28:03 ]

S29GL256P90FFSS7

guliver

Hi , I have a VP890 and I need to program a Spansion ebga64, S29GL256P90FFSS7, It´s possible ? Can I use other model from software ? Tks

Last post : Re:S29GL256P90FFSS7	Reply: lxx
Please select S29GL256PxxFFI01 and try.

All replies (1)

[ Posted:2012-07-17 09:22:02 ]

VP990 and NAND HYNIX H27UBG8T2ATR

xerius

Hi! Could you add NAND HYNIX H27UBG8T2ATR to my programmer?
Datasheet HERE
Thank you!

Last post : Re:VP990 and NAND HYNIX H27UBG8T2ATR	Reply: xerius
ok. i send email.

All replies (5)

[ Posted:2012-07-13 14:08:09 ]

vp-990

aiman said register

Are vp-990 able to put the chips Basoord and delete with an explanation of the steps and Thank you

Last post : Re:vp-990	Reply: lxx
Sorry. Basoord? I don"t understand that you say.

All replies (1)

[ Posted:2012-07-13 04:43:58 ]

VP890 Advanced Mode

ciariello

Dear Sir,
i think your products are made for professional user.
Why don"t　you add an "Advanced Mode" (Offset settings,Voltage settings,Verify while write enable/disable mode,bad block indicator) so every user can create himself the right settings for new devices?
So every user could use his Wellon Programmer at Maximum of potentiality!!!
This could be the right way to create a　database shared between all the users and you can save much work!!!

Could be really great

thank you very much for your precious time.

P.S. - is there a way to expand the Programmer Hardware buffer to be able to read/ write nand over or equal 4GB ? -

[ The message is modified by ciariello ]

Reply the message

[ Posted:2012-07-12 23:39:20 ]

vp-990

aiman said register

What is the difference between wellon vp-990 and wellon vp890

Last post : Re:vp-990	Reply: lxx
VP-990 support more devices.

All replies (1)

[ Posted:2012-07-11 08:05:46 ]

Anyone tried 74194 with VP-280

AlexJ

Hello,
All 74194 I tried failed, with error code :
　Expected: V0007:1111110G10CLLLHV
　Result　: V0007:1111110G10CLLHHV
Anyone already tried this component ?
(FYI my programmer works fine with all other component)
Bye

Last post : Re:Anyone tried 74194 with VP-280	Reply: lxl
1.maybe your VP-280 is bad. 2 maybe your chip is partly bad

All replies (3)

[ Posted:2012-07-08 18:48:13 ]

VP-290 and GAL22V10

blarsen

I have a VP-290 programmer.　I am trying to program a Lattice GAL22V10 chip.　It programs every fuse correctly except bit 44.　I"ve tried using several different chips.　I"ve altered the tPW setting.　I"ve downloaded the Wellon software from the web.　Any ideas why bit 44 never programs correctly?

Last post : Re:VP-290 and GAL22V10	Reply: lxl
please email its .jed file to weilong@weilei.com.cn

All replies (1)

[ Posted:2012-07-03 02:55:30 ]

Dead VP-280 after software update online

spacewalker register

Hello.I was try to Software update online, and software frozen. After this, Programmer have only RER LED, PC and　Software not recognize this device now. I download the lates from Download Aread but still this same problem.

Last post : Reply	Reply: hlark
Please accord to WELLON software,click the list "Help"->"Contents",Chapter3.7 Error message,"If your programmer that had the function of update online lost its program, you can resume it".Do as what follows.

All replies (1)

[ Posted:2012-06-27 16:44:26 ]

WL-SOJ42(400)-U1

farhad

Hi.If possible , please send me the WL-SOJ42(400)-U1 schematic or datasheet.Thanks alot.

Last post : Re:WL-SOJ42(400)-U1	Reply: lxx
You can find it from software. "Help"--"Adapter"

All replies (1)

[ Posted:2012-06-23 23:01:36 ]

VP-990

farhad

Hi. The latest software ,,System Update,, dos not work.I test with VP-990.

Last post : Re:VP-990	Reply: lxl
please download new soft.

All replies (1)

[ Posted:2012-06-20 01:19:21 ]

ATMega8

rfhzcx

I have a problem when I want to reprogram an ATMega8 MCU,in VP390 programmer.
I suppose the problem is in inactive RESET pin. I suppose the algorithm doesn"t allow this situation.
Have you ever the same problem ?

Last post : Re:ATMega8	Reply: lxx
We do not find that.Please tell me your software version and your configuration setting.

All replies (5)

[ Posted:2012-05-07 23:26:35 ]

vp-380 not working with PIC 16F84A

Brainman

hello,
i tried programming PIC16F84A with wellon VP-380 programmer,it says programme "OK" display my setting as RC even when changed to Crystal.when i test the programmed chip it does nothing.how can i solve this problem? is it software or firmware problem and where can it be downloaded?

Last post : Re:vp-380 not working with PIC 16F84A	Reply: gxj
I have tested this chip, but I did not find any problems. Please send me your screen picture, include the error information.

All replies (4)

[ Posted:2012-06-14 18:11:46 ]

VP190

bahai.trinh register

I use the VP-190 programmer. Trying write on the SFP EEPROM ACE TECHNOLOGY. It always "failed" Can read but can not write. Looking on the website, it say support device ACE but look at Device selection I don"t see ACE on the list. Can somebody help me on selection device ?

Last post : Re:VP190	Reply: cm
Hello! Please downlaod the newest software in our website.

All replies (1)

[ Posted:2012-06-18 12:29:30 ]

VP-990

farhad

Hi.The latest software dose not work for testing AS4C256K16F0 & AS4C1M16F5 .

Last post : Re:VP-990	Reply: jin
We tested it OK with the latest software. You can choose the option "Insertion Test" first and then test them.

All replies (1)

[ Posted:2012-06-16 18:54:18 ]

X-Gold 608　(PMB8878)

ciariello

Hi guys , can you add this device to Wellon VP-890 programmer?

It"s a Infineon device and it places on the iphone like baseband chip but it"s possible program it by oher programmer (LabTool , UP2008) but i think the VP-890 is better!!!

THANKS A LOT

Last post : Re:X-Gold 608　(PMB8878) Reply: jin registered

You can choose the type "PF38F3050L0YBQ0" to try. And change the VCC and vpp to 1.8V.

All replies (3)

[ Posted:2012-06-10 16:09:32 ]

VP-990

farhad

Hi.I had try with latest software for testing AS4C256K16F0 & AS4C1M16F5 , but dose not work !

Last post : vp-380 not working with PIC 16F84A	Reply: Brainman
hello, i tried programming PIC16F84A with wellon VP-380 programmer,it says programme "OK" display my setting as RC even when changed to Crystal.when i test the programmed chip it does nothing.how can i solve this problem? is it software or firmware problem and where can it be downloaded?

All replies (2)

[ Posted:2012-06-13 19:34:58 ]

VP-990

farhad

Hi.When I test AS4c256K16F0 & AS4C1M16F5 with my vp-990 , show: Test fail!I had try with new devices and end software update but dose not work.

[ The message is modified by farhad ]

Last post : Re:VP-990	Reply: jin
We have modified our software, please download our latest software to try.

All replies (1)

[ Posted:2012-06-12 02:11:31 ]

Vp890 Intel 28F320j3D 75

guliver

Hi, I try to reprogram a Intel bga64 28F320 j3 D75. I use adapter WL-EBGA64-P-30 and not erase the flash. Programmer initiate success !　ERASE Fail 86,47sec.　Its necessary change any setting ? I try with 3 flashs, and result is error. Tks

Last post : Re:Vp890 Intel 28F320j3D 75	Reply: jin
You can read the chip first. Then click "Config" and you can see the data of OTP area on the frame of "Edit Configuration".

All replies (5)

[ Posted:2012-05-27 16:07:07 ]

s29GL032N90FFIS1 and s29gl032N90FFIS2

guliver

Hi , I need to program a Spansion ebga64,　s29gl032N90FFIS1 and　s29gl032N90FFIS2, flash. I have a VP890. It´s possible ? Can I use other model ? I use adapter WL-EBGA64-320+, tks

Last post : Re:s29GL032N90FFIS1 and s29gl032N90FFIS2	Reply: jin
Please try to choose S29GL032NxxFFI01 to write S29GL032N90FFIS1/2.

All replies (1)

[ Posted:2012-05-30 14:01:34 ]

Run-time error 3450 on VP980

Fastah

Hi
I found error in new software 4.4.0. When autodetect device (eprom) program detect device and when select device from list say: "Run-time error "3450": Syntax error in query. Incomplete query clause."
Second, please correct window sizes　when autodetect device. If program give more than two types, must click right on arror to view full list of suggested devices. In old version these window sizes are higher and fit three or more devices

Last post :

Re:Run-time error 3450 on VP980

Reply: Fastah registered

Hi
Just download last version 4.4.0 (29.05.2012), window size corrected but still Run-time error 3450 on autodetect device. I have WinXP Pro with SP3.
I will also test on another computer tomorrow and inform you.

Thank you

All replies (2)

[ Posted:2012-05-26 23:28:19 ]

VP-280 and 27C256 (PLCC)

ElBarto

Hello,

I have the VP-280 programmer with the WL-PL32-U1 adapter.
I want to dump the content of a PLCC 27C256 but with the adapter the pins aren"t compatible with a DIP 27C256.
Is it possible to update the software/firmware for that ?

Thanks.

Last post : Re:VP-280 and 27C256 (PLCC) Reply: lxl Host

sorry,you need use WL-PL32-P2

All replies (1)

[ Posted:2012-05-28 17:53:13 ]

Program BIOS (ESMT F25L008A) w/ VP-280?

novusdin

Hi, I want to program an SPI/SPROM BIOS-chip (taken from ECS A780GM-A Mainboard) = ESMTF25L008A-50. I tried different chips from the database (like EON 25T80), but I can"t program the chip. I can read and erase the chip without problems. But programming won"t work. Is there a way to solve this problem? I am using VP-280 (Firmware v12.0).

Last post : Re:	Reply: cm
Hello! The chip F25L080 is different from EN2T80. The programmer VP-280 didin"t support F25L080.

All replies (1)

[ Posted:2012-05-28 00:57:54 ]

VP890 and Attiny88PA

guliver

Hi, I need use a security, FUSES, but not works for me, any hits ?

Last post : Re:VP890 and Attiny88PA	Reply: guliver
Ok,　problem solved, thks

All replies (2)

[ Posted:2012-05-26 14:09:30 ]

Reading/Writing to MX29LV320DBTI-70G

MisteryMan register

Hello, I Have a VP-480 (f/w 12.0) and I am having problems recognising a 48pin TSOP. It is a MX29LV320DBTI-70G. The problem is that I can"t read or write to it as it keeps failing to detect pin 37. I have tried this on several of these TSOPs and exactly the same, yet if I put a Spansion S29AL032D90TF into the same adaptor it reads and writes fine. Is there some protection on this chip? Will I be able to read and program to it? Thank you :)

Last post : Re:Reading/Writing to MX29LV320DBTI-70G	Reply: lxl
There is not protection on this chip.you can disable "Insertion Test". if program fail,maybe your chip is bad

All replies (2)

[ Posted:2012-05-19 17:33:56 ]

VP-290 Install Problem

trich

When I try to install the product under XP I get the message
"An error occurred during the installation of the device
A service installation section in INF is invalid"

When I try to install the device under Windows 7 I get the message
"Windows cannot load the device driver for this hardware (Code 39)"
Driver date 9/12/2009
Version 2.0.0.18

What can I do to get the product working under either OS.

Last post : Re:VP-290 Install Problem Reply: lxx registered

Please try again. If not, please download from http://www.programatory.pl

All replies (6)

[ Posted:2012-05-22 14:58:15 ]

Hynix H27UBG8T2ATR

ciariello

Dear Sir, i really need support to read/program this nand. Please help me. I know you can do it.THANK YOU VERY MUCH

[ The message is modified by ciariello ]

Last post : Re:Hynix H27UBG8T2ATR	Reply: jin
Sorry, we can"t support the chip like so large capacity.

All replies (1)

[ Posted:2012-05-24 13:54:00 ]

vp-990

aiman said register

Hello
I request you to explain the history list in the new program"s interface and I request you to explain how the use of note that I used vp990

Last post : Re:vp-990	Reply: lxx
When you select a chip and click "OK", history list will have a record.When you select the chip next, you can select it from history list.

All replies (1)

[ Posted:2012-05-25 05:52:05 ]

vp-990

aiman said register

Hello
I request you to explain the history list in the new program"s interface and I request you to explain how the use of note that I used vp990

Reply the message

[ Posted:2012-05-25 06:04:10 ]

vp 990

aiman said register

vp 990　 an82527

http://www.datasheetcatalog.com/datasheets_pdf/A/N/8/2/AN82527.shtml

Last post : Re:vp 990	Reply: lxl
this chip do not need program.

All replies (1)

[ Posted:2012-05-24 01:57:32 ]

VP-280 - problem writing 27128

lrrosa

Hi, I have four eproms NMC27CP128Q250.
I tried to write them all with my VP-280 but without success.
I always erase them first (blank check OK) and use the AC adapter.

The error I get is this:
>>.Program......
>>Device Address:000100H　Device Data:E1H　Buffer Address:000100H　Buffer Data:E9H
>>Program fail!
>> 1,03Sec

I appreciate any help, thanks.

Last post : Re:VP-280 - problem writing 27128 Reply: lxl Host

Maybe the chip is bad,usually this chip is older

All replies (1)

[ Posted:2012-05-21 08:43:47 ]

VP 890 install problem

naingwin

I HAVE VP890 PROGRAMMER.my programmer is all ok using old soft.
now i update ver 4.4.0 ver, It is not working..Installation　is completed.but i run the program,it is open ok,i select chip,it show this message "Run-time error_2147024769(8007007 f)automation error.the specified procedure could not be found."
"run time error"13".type mismatch."
what problem.

Last post : Re:VP 890 install problem	Reply: cm
Our software have some .dll of windows system. So, please download the windows system patch in the web, include SP3 and other system patch.

All replies (1)

[ Posted:2012-05-19 18:19:24 ]

vp-890 to vp-990

daddy

is it possible to upgrade vp-890 to vp-990
does vp-890 and vp-990 work with the same software

[ The message is modified by daddy ]

Last post : Re:vp-890 to vp-990	Reply: lxx
No.

All replies (1)

[ Posted:2012-05-17 10:31:14 ]

VP-890 Xilinx problems (SOLVED)

ciariello

i am trying to program a Coolrunner CPLD XC2C64 with TQFP adapter....but it fails!!! i am trying svf files and don"t work but SEEMS works with jed files.

[ The message is modified by ciariello ]

Last post : Re:VP-890 Xilinx problems	Reply: ciariello
i tried it and it works with X2C64A ...great job

All replies (24)

[ Posted:2012-03-16 15:04:27 ]

VP-890 add Hynix　H27UBG8T2ATR

ciariello

hi to everyone, soon will arrive to me from china my new Wellon VP-890 but reading the devices list i noticed that H27UBG8T2ATR misses.
Is it possible add it ?
thank you very much

Last post :

Re:VP-890 add Hynix　H27UBG8T2ATR

Reply: ciariello registered

Then the VP-890 can read flash until 1Gb max?

if you could add it....will be really great

thanks for your great support

[ The message is modified by ciariello ]

All replies (6)

[ Posted:2012-03-05 19:52:00 ]

VP-890 Phison PS7000

ciariello

hi could you add Phison PS7000 to my programmer? I think is an eMMC device. Could be really great....thank you

Last post : Re:VP-890 Phison PS7000	Reply: lxl
please offer its datasheet

All replies (1)

[ Posted:2012-05-12 03:22:34 ]

VP-980 latest firmware

Fastah

Please tell me latest firmware revision of VP-980. I have v9.0 and Software update on 4.3.2 or later say message "During system update do not put off programmer power !" and can push System Update or Cancel. Does my programmer can be updated?

Thank you.

[ The message is modified by Fastah ]

Last post : Re:VP-980 latest firmware	Reply: hlarkhlark
If your programmer works well, you needn"t to update the firmware version.If it doesn"t work well, you can try to update it to the newest firmware version.

All replies (1)

[ Posted:2012-05-07 04:50:58 ]

Top2007

Manoj

I am using Top2007 need support

Last post : Re:Top2007	Reply: lxl
Sorry,it is not our product.

All replies (3)

[ Posted:2012-05-04 21:39:46 ]

hy27us081

daddy2006

with which product can i program this ?

Last post : Re:hy27us081	Reply: lxl
VP-990　GP-10/20/201

All replies (1)

[ Posted:2012-05-04 11:24:44 ]

VP-290 communication error

Hello
our brand new VP290 doesn"t work:
We tried to program P89V51RD2BN and P89C51RD2HBP DIL40, brand new!
Step "Blank check" is o.k.
Step "Erase" is done without errors
Step "Program" is done without errors
Step "verify" says: communication error (In the big output window)
Sometimes a message appears like "Need AC Adaptor" even when the AC Adaptor is connected (Supplies the 9V DC, o.k.)

Initialization was o.k.
All tests o.k. (5V, 12V, system...)

Last post : Re:VP-290 communication error Reply: lxl Host

Please run the "system update" in the menu "help".

All replies (1)

[ Posted:2012-05-02 19:29:13 ]

Total 1464,Total 30 pages

[<<][20][>>]

search: title content user

Web homepage | Contact us | About us

Tianjin Weilei Technology Ltd.

264.65 ms